Hi Toube,
there is no WOL support on our loved Raspberry Pis.
Frank
by hondagx35 » 03 Nov 2018, 23:47
by Toube » 04 Nov 2018, 08:07
hondagx35 wrote:Hi Toube,
there is no WOL support on our loved Raspberry Pis.
Frank
by s.k. » 04 Nov 2018, 21:40
by janui » 04 Nov 2018, 23:18
See here: post25866.html?hilit=bluetooth#p25862s.k. wrote:the proper way to deactivate the Bluetooth and the Wi-Fi in the Pi2 image ?
by hondagx35 » 04 Nov 2018, 23:23
Name: pi3-disable-bt
Info: Disable Pi3 Bluetooth and restore UART0/ttyAMA0 over GPIOs 14 & 15
N.B. To disable the systemd service that initialises the modem so it
doesn't use the UART, use 'sudo systemctl disable hciuart'.
Load: dtoverlay=pi3-disable-bt
Params: <None>
Name: pi3-disable-wifi
Info: Disable Pi3 onboard WiFi
Load: dtoverlay=pi3-disable-wifi
Params: <None>
pi3-disable-wifi
pi3-disable-bt
systemctl disable hciuart
by s.k. » 04 Nov 2018, 23:26
by s.k. » 05 Nov 2018, 00:10
s.k. wrote:@ all
Does anyone manage to install a remote control successfully?
/usr/lib/systemd/system/irexec.service
/etc/lirc/lirc_options.conf
/etc/conf.d/lircd.conf
/boot/config.txt
dtoverlay=lirc-rpi
dtparam=gpio_out_pin=7
dtparam=gpio_in_pin=22
/etc/lirc/lircd.conf.d/lircd.conf
begin remote
name apple
bits 8
flags SPACE_ENC|CONST_LENGTH
eps 30
aeps 100
header 9140 4390
one 608 1618
zero 608 518
ptrail 610
repeat 9141 2157
pre_data_bits 16
pre_data 0x77E1
post_data_bits 8
post_data 0x79
gap 107219
toggle_bit_mask 0x0
begin codes
KEY_UP 0x50 # Was: UP
KEY_DOWN 0x30 # Was: DOWN
KEY_LEFT 0x90 # Was: LEFT
KEY_RIGHT 0x60 # Was: RIGHT
KEY_PLAY 0xFA # Was: PLAY
KEY_MENU 0xC0 # Was: MENU
KEY_OK 0x3A # Was: OK
end codes
end remote
systemctl start lircd
irw
systemctl enable lircd
/etc/conf.d/lircrc
begin
prog = irexec
remote = apple
repeat = 0
button = KEY_PLAYPAUSE
config = mpc toggle
end
begin
prog = irexec
remote = apple
button = KEY_RIGHT
repeat = 0
config = mpc next
end
begin
prog = irexec
remote = apple
button = KEY_LEFT
repeat = 0
config = mpc prev
end
begin
prog = irexec
remote = apple
button = KEY_UP
delay = 2
repeat = 10
config = mpc volume +2
end
begin
prog = irexec
remote = apple
button = KEY_DOWN
delay = 2
repeat = 10
config = mpc volume -2
end
begin
prog = irexec
remote = apple
button = KEY_MENU
button = KEY_DOWN
button = KEY_OK
repeat = 0
config = systemctl poweroff
end
systemctl enable irexec.service
by MikeC » 05 Nov 2018, 16:49
by Toube » 05 Nov 2018, 17:52
by cmh714 » 05 Nov 2018, 18:01
Toube wrote:I'm still using the first version 20180903.. since I tried the gitpull from the dev a week ago and after I tried to reboot it wouldn't start so I flashed it back to the first version.
Should the gitpull from dev work or do one need to use the command interpreter for this?
-Toube
support RuneAudio