RuneAudio 0.4-beta for Raspberry Pi2/3

Airstone

Hello! Is it possible to install 0.4 beta version above 0.3 beta without removal old one and with keeping previous settings? Thanks.

Ancipital

Airstone wroteHello! Is it possible to install 0.4 beta version above 0.3 beta without removal old one and with keeping previous settings? Thanks.

See the answer on the first page of this thread:

#44347

luamiennam

Hello, I can't config ip for my usb wifi ( LAN & Wifi onboard on ).
Sorry, my english is not good.

vbondarev

Any news about read-only system?

hondagx35

luamiennam wroteHello, I can't config ip for my usb wifi ( LAN & Wifi onboard on ).
Sorry, my english is not good.

Hi,

it is not possible to use more than one wifi at the moment, so you should disable the onboard wifi first.
#43908

Frank

luamiennam

hondagx35 wrote
luamiennam wroteHello, I can't config ip for my usb wifi ( LAN & Wifi onboard on ).
Sorry, my english is not good.
Hi,

it is not possible to use more than one wifi at the moment, so you should disable the onboard wifi first.
#43908

Frank

Thanks

.
I have a question: when using AP (wifi on board), I must have to attach the cable to the LAN port?

Kilgore

This may be a dumb question, but...........

If I select an I2S kernel module (for example HiFiBerry Digi/Digi+), and then reboot, should it list in the MPD 'Audio Output Interface', even if the board (+Digi+ Pro) is faulty or disconnected?

I ask because it was all working OK until a day ago when I took my setup apart to implement some power supply changes. I powered up and now I have no output from the digi+. (I have USB output from the Pi and this works OK in my DAC, so the Pi is OK)

I have downloaded the latest rune 0.4 beta image from Franks Google Drive today and reloaded my SD card, but although I have tried selecting the Digi in the I2s Settings, it doesn't list in MPD output interface dropdown. it is not clear to me if perhaps I have busted my digi+ so it does not list.....or if there is some setting I am missing.

hondagx35

Hi Kilgore,

If I select an I2S kernel module (for example HiFiBerry Digi/Digi+), and then reboot, should it list in the MPD 'Audio Output Interface', even if the board (+Digi+ Pro) is faulty or disconnected?

This depends on the selected driver!
The HifiBerry Digi/Digi+ needs to be attached and recognized by the driver to show up on the mpd outputs.

Frank

Ancipital

Do you see the Digi if you ssh in and type:

aplay -l

If the module is loaded and the hardware working, it will show up there- if it doesn't, then that's where to start looking. If you can't see the module loaded when you type:

lsmod | grep hifiberry

..that might be relevant too.

Edit:

Ninja-ed by frank

hondagx35

luamiennam wroteI have a question: when using AP (wifi on board), I must have to attach the cable to the LAN port?

No, you don't!

But if you like to play music from network storage you need a separate network connection (ethernet).

You can use wlan0 and wlan1 together, but it can not be configured from Rune UI.
Manual configuration shouldn't be hard,

Frank

coley 20001

Hi everyone
I am complete novice when it comes to this kind of thing but I managed to get my raspberry pi 3 with allo boss dac up and running following the info from the forum so would like to thank all involved with rune.
Coley20001

foogaamoo

Tested it on RPI2B with IQAudio DigiAMP+. Could you add hardware unmuting if you pick IQaudIO PI-DAC+ for i2s kernel modules section on the settings page?

It's a broken experience for the casual or new user having to manually do these steps:

[root@iqaudio ~]# echo "22" > /sys/class/gpio/export
[root@iqaudio ~]# echo "out" > /sys/class/gpio/gpio22/direction
[root@iqaudio ~]# echo "1" > /sys/class/gpio/gpio22/value

So far really enjoying the password login as this device is being used in a shared network for web radio and airplay. Kudos for all the effort!

luamiennam

hondagx35 wrote
luamiennam wroteI have a question: when using AP (wifi on board), I must have to attach the cable to the LAN port?
No, you don't!

But if you like to play music from network storage you need a separate network connection (ethernet).

You can use wlan0 and wlan1 together, but it can not be configured from Rune UI.
Manual configuration shouldn't be hard,

Frank

Thanks Frank

Cyclopse

Rasberry Pi 2 and version 0.4b build 29feb2017

Problem with the Spotify interface. I can see the playlist and when I select a track no audio and fails to play. Read about changing audio interface to analogue and back. However, I only have my USB dac listed in the audio output interface, no other options in the drop down box.

Any suggestions most welcome.

Thanks

Cyclopse

hondagx35

Hi Cyclopse,

However, I only have my USB dac listed in the audio output interface, no other options in the drop down box.

try to temporarily enable HDMI and 3,5mm jack on the settings page.

Frank

donimo

Hi Frank,
Thank You for the update.
Like a couple of other users, the screensaver feature where the UI changes to artist info and lyrics is not functioning reliably.
I have the latest 0.4 build, Raspberry Pi 3 and a Waveshare 5" HDMI display.
You did mention a few pages back it may be a touchscreen issue - do you have any further information or help?
The same thing happens on my local browser running chrome on a PC, which is definitely not a touchscreen!

hondagx35

Hi donimo,

artist info and lyrics is not functioning reliably

What is the exact problem?

Frank

donimo

hondagx35 wroteHi donimo,

artist info and lyrics is not functioning reliably
What is the exact problem?

Frank

Every 20 - 25 seconds the standard screen flicks to the 'artist info' screen for approximately 0.5 seconds, then back.
My main use is web radio, so I have left it alone. After 10 - 12 mins, I noticed the display was steady on 'artist info' screen.
A single touch returns the screen to standard but then the flicking starts again.

debug data;
https://pastebin.com/h3CYbJ5i

SeanWu

Is 20170229 the latest build for RuneAudio 0.4 beta?
I just get Allo Boss DAC and want to make sure that this build is compatible with the DAC.

hondagx35

Hi SeanWu,

Is 20170229 the latest build for RuneAudio 0.4 beta?

Yes, it is.

I just get Allo Boss DAC and want to make sure that this build is compatible with the DAC.

"Allo Boss DAC" is supported with this image. It can be selected on the settings page.

Frank

« Previous Page Next Page »