rav666 Raspberry Pi2 with a TSOP4838 IR Receiver to Raspberry Pi, connected to 3.3v, ground and Data to pin 18 PART 1 : First install volumio 2.0.31 to get a lircd.conf and lircrc file using winscp this is works perfectly for me > u:volumio p:volumio sudo apt-get update sudo apt-get install lirc sudo nano /etc/lirc/hardware.conf >> LIRCD_ARGS="--uinput" .......... DRIVER="default" ........... DEVICE="/dev/lirc0" ........... MODULES="lirc_rpi" >> sudo nano /boot/config.txt >> dtoverlay=lirc-rpi,gpio_in_pin=18 ls /dev You should see a list of /dev entries. Search for '/lirc0' entry. If you see it, you've got it. Now let's if it is working properly… sudo modprobe lirc_rpi mode2 -d /dev/lirc0 test some buttons ? sudo /etc/init.d/lirc stop irrecord -n -d /dev/lirc0 ~/lircd.conf sudo mv ~/lircd.conf /etc/lirc/lircd.conf sudo /etc/init.d/lirc start irw test some more buttons sudo nano /etc/lirc/lircrc >> begin prog = irexec button = KEY_PLAY config = mpc toggle end begin prog = irexec button = KEY_NEXT config = mpc next end begin prog = irexec button = KEY_PREVIOUS config = mpc prev end begin prog = irexec button = KEY_VOLUMEUP config = mpc volume +5 repeat = 4 end begin prog = irexec button = KEY_VOLUMEDOWN config = mpc volume -5 repeat = 4 end begin prog = irexec button = KEY_STOP config = mpc toggle end begin prog = irexec button = KEY_FWD config = mpc seek +00:00:15 repeat = 0 end begin prog = irexec button = KEY_RWD config = mpc seek -00:00:15 repeat = 0 end begin prog = irexec button = KEY_SHUFFLE config = mpc random repeat = 0 end >> Make sure to get the lircd.conf and lircrc files using winscp !! PART 2 : user: root password: rune nano /boot/config.txt find this uncomment the 2 lines >> dtoverlay=lirc-rpi #dtparam=gpio_out_pin=17 dtparam=gpio_in_pin=18 #dtparam=gpio_in_pull=down >> nano /etc/conf.d/lircd.conf >> LIRCD_ARGS="--uinput" DRIVER="default" DEVICE="/dev/lirc0" MODULES="lirc_rpi" >> systemctl reboot copy volumio conf > here, overwrite if needed /etc/lirc/lircd.conf.d/lirc.conf (updated 12/02/2017) systemctl start lircd irw (you should see output like this if your lucky) [root@runeaudio ~]# irw 000000037ff00be9 00 KEY_PLAY /home/volumio/lircd.conf 000000037ff00be5 00 KEY_NEXT /home/volumio/lircd.conf 000000037ff00be4 00 KEY_PREVIOUS /home/volumio/lircd.conf 000000037ff00bea 00 KEY_RWD /home/volumio/lircd.conf 000000037ff00beb 02 KEY_FWD /home/volumio/lircd.conf 000000037ff00bef 02 KEY_VOLUMEUP /home/volumio/lircd.conf 000000037ff00bee 00 KEY_VOLUMEDOWN /home/volumio/lircd.conf 000000037ff00bdb 04 KEY_SHUFFLE /home/volumio/lircd.conf systemctl enable lircd copy lircrc from volumio> here, again overwrite to /etc/conf.d/lircrc nano /usr/lib/systemd/system/irexec.service >> [Unit] Description=Start irexec daemon Wants=lircd.service After=network.target [Service] Type=simple ExecStartPre=/usr/bin/sh -c "sleep 3" ExecStart=/usr/bin/irexec /etc/conf.d/lircrc [Install] WantedBy=multi-user.target >> systemctl enable irexec.service
hondagx35 Hi rav666, sudo apt-get update sudo apt-get install lirc sudo nano /etc/lirc/hardware.conf This will not work with Rune Audio, because we use Arch Linux. On Arch Linux you can install packages with "pacman -S xxxxxx" Frank
rav666 the first part is for volumio, the second part is for runeaudio This was just so that I could get the lirc files I needed for rune Runeaudio was the only player that could deal with my music shares without bombing out !!
mecaz hello i followed your guide and created lirc.conf file with my remote and receiver. but when i executed irw notthing appears at screen. i wonder can you make a clear guide only for runeaudio that shows step by step what to do? Regards
