No Music - all I did was unplug and pluged in Toshlink

foxint

Hi Guys...

I am going to have to retire ....hurt....

All was good.... I decided to try and install a toslink splitter into the equation - my thinking conntect the pc to one hole and the Pi to the other hole and what ever was working would come out the single hole...yes all very technical

swapped some cable and of course it did not work....so I replace the cables as before NO SOUND.....

Rebooted, re-started NOTHING.

there is a red light at the optical out on the Digi + (yes checked it was digi).... so I swapped the cable (optical) to the optical of the PC....NOISE.-MUSIC...swapped it to the Pi NO NOise...all was working 30min ago and I have done nothing but unplug and plug....

No I do not have a long enough RCA cable to check this on the Digi....but if there is a light...there should be NOISE???

Sorry guys... I am jinxed....

HELP.

rikardo1979

foxint wroteHi Guys...

I am going to have to retire ....hurt....

All was good.... I decided to try and install a toslink splitter into the equation - my thinking conntect the pc to one hole and the Pi to the other hole and what ever was working would come out the single hole...yes all very technical

swapped some cable and of course it did not work....so I replace the cables as before NO SOUND.....

Rebooted, re-started NOTHING.

there is a red light at the optical out on the Digi + (yes checked it was digi).... so I swapped the cable (optical) to the optical of the PC....NOISE.-MUSIC...swapped it to the Pi NO NOise...all was working 30min ago and I have done nothing but unplug and plug....

No I do not have a long enough RCA cable to check this on the Digi....but if there is a light...there should be NOISE???

Sorry guys... I am jinxed....

HELP.

is your DAC selected and set properly in system as audio OUT?

rastus

foxint wrotethere is a red light at the optical out on the Digi + (yes checked it was digi)....

rikardo1979 > It's not a DAC, it's a DIGI.

With my DIGI+, I broke the weld on the coax connector to the board trying to put the damned cable in, so I only used the optical connection after that. Maybe check that the welds haven't broken on the optical cable connector attached to the board.

rikardo1979

rastus wrote
foxint wrotethere is a red light at the optical out on the Digi + (yes checked it was digi)....
rikardo1979 > It's not a DAC, it's a DIGI.

With my DIGI+, I broke the weld on the coax connector to the board trying to put the damned cable in, so I only used the optical connection after that. Maybe check that the welds haven't broken on the optical cable connector attached to the board.

still need to be added into config or not?

OP2

rastus

rikardo1979 wrotestill need to be added into config or not?

Well yes rikardo, of course it needs to be added in config... but... a DIGI needs to be added, not a DAC.

rikardo1979

rastus wrote
rikardo1979 wrotestill need to be added into config or not?
Well yes rikardo, of course it needs to be added in config... but... a DIGI needs to be added, not a DAC.

i didnt even check what digi is but same apply to all.
That was my point

OP2

rastus

rikardo1979 wrotei didnt even check what digi is but same apply to all.
That was my point

You didn't check what? It is a different config setting for the DIGI than DAC? No? Or is it the same? I'm not sure I see, or understand, your point rikardo, am I missing something?

rastus

foxint > Did you end up figuring this out? What went wrong? Must have feedback, sitting on the edge of my seat here.... waiting with baited breath....

foxint

Mate
Been off the air for a while...but it seems to work...not sure what I did

Thanks