Well, the MPD was adding Music to the library. After a reboot it looks fine, but it's hard to add it all without a crash (60k - so it's a huge library).
The top looks fine now, after the reboot. It sounds like you're right about the MPD high load bug.
After the reboot i tried to add the .mp3 station, with no problems at all - So it was definitely the MPD process.
Edit: And i almost forgot to mention that the AutoHotkey scripts still works fine (like it also should ofc.
)
Update 1:
A moment ago, i was playing a radio station - and looked at my library, but i could not find my NAS. After visiting the Sources page, and saved the NAS settings again, it crashed. (
https://www.dropbox.com/s/u6r5nzhh0t0tael/Screenshot%202014-07-10%2022.48.54.png)
As you can see, it looks like the MPD crashed. Then i visited the Sources page, i just got the "Not able to connect to the network", or a message like that.
Update 2:
After a fresh reboot (with the reboot command over the SSH) i got the same problem.
https://www.dropbox.com/s/l2ezplfrt8d9wiw/Screenshot%202014-07-10%2022.54.48.png (Screenshot of Sources)
But at this time, i was able to press the "Save Mount" button again, without getting a crash. Looks a bit like it has some problems then mount the partition at boot.
Update 3:
I tried to reboot the Pi, then the MPD was updating the library. It looks a bit like it has problems with the reboot. I wasn't able to connect to it, after calling a reboot from the WebUI. I took the plug out, and powered it up again, without any problems at all.
But now i'm not able to browse my NAS again. Where's the output:
- Code: Select all
###### System info ######
Linux version 3.12.19-2-ARCH (root@CS) (gcc version 4.8.2 20131219 (prerelease) (GCC) ) #1 PREEMPT Thu May 22 15:35:00 UTC 2014
system time: Thu Jan 1 00:00:54 UTC 1970
system load: 0.94 0.27 0.09 1/83 355
HW platform: RaspberryPi (01)
playerID: 018a9ae97357c941451ab81b601dfaaf4f
###### System load statistics (procinfo -H) ######
Memory: Total Used Free Buffers
RAM: 183.55MiB 110.74MiB 72.81MiB 12.05MiB
Swap: 0.00B 0.00B 0.00B
Bootup: Thu Jan 1 00:00:00 1970 Load average: 0.94 0.27 0.09 1/84 357
user : 00:00:10.64 19.8% page in : 72890
nice : 00:00:00.00 0.0% page out: 1552
system: 00:00:08.82 16.4% page act: 3571
IOwait: 00:00:02.72 5.1% page dea: 0
hw irq: 00:00:00.24 0.4% page flt: 118524
sw irq: 00:00:00.32 0.6% swap in : 0
idle : 00:00:30.92 57.6% swap out: 0
uptime: 00:00:54.53 context : 36891
irq 3: 21551 irq 75: 1
irq 16: 0 irq 77: 7123
irq 32: 18548 irq 79: 0
irq 52: 0 irq 80: 0
irq 65: 4 irq 84: 12141
irq 66: 1
mmcblk0 2169r 1 sda 0r 0w
mmcblk0p1 87r sdb 0r 0w
mmcblk0p2 2r sdc 0r 0w
mmcblk0p3 50r sdd 0r 0w
mmcblk0p5 1970r sde 114r 0w
eth0 TX 0.00B RX 0.00B wlan0 TX 0.00B RX 0.00B
lo TX 93.92KiB RX 93.92KiB
###### Active processes (pstree) ######
systemd-+-agetty
|-avahi-daemon---avahi-daemon
|-avahi-dnsconfd
|-dbus-daemon
|-debug_collector---sh---pstree
|-devmon---sleep
|-ifplugd
|-mpd---4*[{mpd}]
|-nginx---nginx
|-nmbd
|-php-fpm---3*[php-fpm]
|-redis-server---2*[{redis-server}]
|-refresh_nics
|-rpc.idmapd
|-rpc.statd
|-rpcbind
|-rune_PL_wrk
|-rune_SY_wrk
|-shairport---{shairport}
|-sshd
`-systemd-udevd
###### Audio backend ######
Advanced Linux Sound Architecture Driver Version k3.12.19-2-ARCH.
Card list: (/proc/asound/cards)
--------------------------------------------------
0 [ALSA ]: bcm2835 - bcm2835 ALSA
bcm2835 ALSA
PLAYBACK devices: (aplay -l)
--------------------------------------------------
**** List of PLAYBACK Hardware Devices ****
card 0: ALSA [bcm2835 ALSA], device 0: bcm2835 ALSA [bcm2835 ALSA]
Subdevices: 8/8
Subdevice #0: subdevice #0
Subdevice #1: subdevice #1
Subdevice #2: subdevice #2
Subdevice #3: subdevice #3
Subdevice #4: subdevice #4
Subdevice #5: subdevice #5
Subdevice #6: subdevice #6
Subdevice #7: subdevice #7
card 0: ALSA [bcm2835 ALSA], device 1: bcm2835 ALSA [bcm2835 IEC958/HDMI]
Subdevices: 1/1
Subdevice #0: subdevice #0
PCM devices: (aplay -L)
--------------------------------------------------
null
Discard all samples (playback) or generate zero samples (capture)
default:CARD=ALSA
bcm2835 ALSA, bcm2835 ALSA
Default Audio Device
sysdefault:CARD=ALSA
bcm2835 ALSA, bcm2835 ALSA
Default Audio Device
Simple mixer controls: (amixer scontrols)
--------------------------------------------------
card 0:
Simple mixer control 'PCM',0
Mixer controls: (amixer controls)
--------------------------------------------------
card 0:
numid=3,iface=MIXER,name='PCM Playback Route'
numid=2,iface=MIXER,name='PCM Playback Switch'
numid=1,iface=MIXER,name='PCM Playback Volume'
numid=5,iface=PCM,name='IEC958 Playback Con Mask'
numid=4,iface=PCM,name='IEC958 Playback Default'
###### mpd.conf ######
###################################
# Auto generated mpd.conf file
# please DO NOT edit it manually!
# Use RuneUI MPD config section
###################################
zeroconf_enabled "yes"
zeroconf_name "runeaudio"
bind_to_address "/run/mpd.sock"
bind_to_address "any"
port "6600"
max_connections "20"
user "mpd"
group "audio"
db_file "/var/lib/mpd/mpd.db"
sticker_file "/var/lib/mpd/sticker.sql"
pid_file "/var/run/mpd/pid"
music_directory "/mnt/MPD"
playlist_directory "/var/lib/mpd/playlists"
follow_outside_symlinks "yes"
follow_inside_symlinks "yes"
auto_update "no"
filesystem_charset "UTF-8"
id3v1_encoding "UTF-8"
volume_normalization "no"
audio_buffer_size "1024"
buffer_before_play "0%"
gapless_mp3_playback "yes"
mixer_type "software"
input {
plugin "curl"
}
decoder {
plugin "ffmpeg"
enabled "yes"
}
state_file "/var/lib/mpd/mpdstate"
audio_output {
name "bcm2835 ALSA"
type "alsa"
device "hw:0,0"
auto_resample "no"
auto_format "no"
enabled "yes"
}
###### Kernel optimization parameters ######
hardware platform: RaspberryPi
current orionprofile: RuneAudio
kernel scheduler for mmcblk0: [noop] deadline cfq
/proc/sys/vm/swappiness: 60
/proc/sys/kernel/sched_latency_ns: 6000000
/proc/sys/kernel/sched_rt_period_us: 1000000
/proc/sys/kernel/sched_rt_runtime_us: 950000
/proc/sys/kernel/sched_autogroup_enabled: 1
/proc/sys/kernel/sched_rr_timeslice_ms: 100
/proc/sys/kernel/sched_min_granularity_ns: 750000
/proc/sys/kernel/sched_wakeup_granularity_ns: 1000000
###### Kernel module snd_usb_audio settings ######
Error opening module snd_usb_audio
###### Systemd active startup scripts (ls -lah /etc/systemd/system/multi-user.target.wants/) ######
total 8.0K
drwxr-xr-x 2 root root 4.0K Jan 1 1970 .
drwxr-xr-x 4 root root 4.0K Jan 1 1970 ..
lrwxrwxrwx 1 root root 44 Jul 22 2013 avahi-daemon.service -> /usr/lib/systemd/system/avahi-daemon.service
lrwxrwxrwx 1 root root 46 Jul 22 2013 avahi-dnsconfd.service -> /usr/lib/systemd/system/avahi-dnsconfd.service
lrwxrwxrwx 1 root root 34 Jan 1 1970 gpio15.service -> /etc/systemd/system/gpio15.service
lrwxrwxrwx 1 root root 40 Jul 2 2014 ifplugd@eth0.service -> /usr/lib/systemd/system/ifplugd@.service
lrwxrwxrwx 1 root root 35 Dec 7 2013 mpd.service -> /usr/lib/systemd/system/mpd.service
lrwxrwxrwx 1 root root 39 Jul 2 2014 netctl@eth0.service -> /etc/systemd/system/netctl@eth0.service
lrwxrwxrwx 1 root root 37 Nov 10 2013 nginx.service -> /usr/lib/systemd/system/nginx.service
lrwxrwxrwx 1 root root 39 Nov 10 2013 php-fpm.service -> /usr/lib/systemd/system/php-fpm.service
lrwxrwxrwx 1 root root 40 Feb 25 2014 rc-local.service -> /usr/lib/systemd/system/rc-local.service
lrwxrwxrwx 1 root root 37 Mar 7 2014 redis.service -> /usr/lib/systemd/system/redis.service
lrwxrwxrwx 1 root root 51 Apr 14 2014 remote-fs.target -> ../../../../usr/lib/systemd/system/remote-fs.target
lrwxrwxrwx 1 root root 39 Jan 1 1970 rpcbind.service -> /usr/lib/systemd/system/rpcbind.service
lrwxrwxrwx 1 root root 42 Jan 1 1970 rpc-idmapd.service -> /usr/lib/systemd/system/rpc-idmapd.service
lrwxrwxrwx 1 root root 41 Jan 1 1970 rpc-statd.service -> /usr/lib/systemd/system/rpc-statd.service
lrwxrwxrwx 1 root root 43 Feb 10 2014 rune_PL_wrk.service -> /usr/lib/systemd/system/rune_PL_wrk.service
lrwxrwxrwx 1 root root 45 Feb 12 2014 rune_shutdown.service -> /usr/lib/systemd/system/rune_shutdown.service
lrwxrwxrwx 1 root root 43 Jan 15 2014 rune_SY_wrk.service -> /usr/lib/systemd/system/rune_SY_wrk.service
lrwxrwxrwx 1 root root 43 Jul 22 2013 sshdgenkeys.service -> /usr/lib/systemd/system/sshdgenkeys.service
lrwxrwxrwx 1 root root 36 Jul 22 2013 sshd.service -> /usr/lib/systemd/system/sshd.service
###### Filesystem mounts ######
rootfs / rootfs rw 0 0
/dev/root / ext4 rw,noatime,nouser_xattr,errors=remount-ro,data=ordered 0 0
devtmpfs /dev devtmpfs rw,relatime,size=89780k,nr_inodes=22445,mode=755 0 0
proc /proc proc rw,nosuid,nodev,noexec,relatime 0 0
sysfs /sys sysfs rw,nosuid,nodev,noexec,relatime 0 0
securityfs /sys/kernel/security securityfs rw,nosuid,nodev,noexec,relatime 0 0
tmpfs /dev/shm tmpfs rw,nosuid,nodev 0 0
devpts /dev/pts devpts rw,nosuid,noexec,relatime,gid=5,mode=620 0 0
tmpfs /run tmpfs rw,nosuid,nodev,mode=755 0 0
tmpfs /sys/fs/cgroup tmpfs ro,nosuid,nodev,noexec,mode=755 0 0
cgroup /sys/fs/cgroup/systemd cgroup rw,nosuid,nodev,noexec,relatime,xattr,release_agent=/usr/lib/systemd/systemd-cgroups-agent,name=systemd 0 0
cgroup /sys/fs/cgroup/cpuset cgroup rw,nosuid,nodev,noexec,relatime,cpuset 0 0
cgroup /sys/fs/cgroup/cpu,cpuacct cgroup rw,nosuid,nodev,noexec,relatime,cpuacct,cpu 0 0
cgroup /sys/fs/cgroup/devices cgroup rw,nosuid,nodev,noexec,relatime,devices 0 0
cgroup /sys/fs/cgroup/freezer cgroup rw,nosuid,nodev,noexec,relatime,freezer 0 0
cgroup /sys/fs/cgroup/blkio cgroup rw,nosuid,nodev,noexec,relatime,blkio 0 0
cgroup /sys/fs/cgroup/perf_event cgroup rw,nosuid,nodev,noexec,relatime,perf_event 0 0
systemd-1 /proc/sys/fs/binfmt_misc autofs rw,relatime,fd=21,pgrp=1,timeout=300,minproto=5,maxproto=5,direct 0 0
debugfs /sys/kernel/debug debugfs rw,relatime 0 0
mqueue /dev/mqueue mqueue rw,relatime 0 0
tmpfs /tmp tmpfs rw 0 0
configfs /sys/kernel/config configfs rw,relatime 0 0
logs /var/log tmpfs rw,nosuid,nodev,noatime,size=5120k 0 0
Ramdisk /run/shm tmpfs rw,nosuid,nodev,noexec,relatime,size=262144k 0 0
rpc_pipefs /var/lib/nfs/rpc_pipefs rpc_pipefs rw,relatime 0 0
rune-logs /var/log/runeaudio tmpfs rw,nosuid,nodev,noatime,size=20480k 0 0
/dev/mmcblk0p1 /boot vfat rw,relatime,fmask=0022,dmask=0022,codepage=437,iocharset=ascii,shortname=mixed,utf8,errors=remount-ro 0 0
###### Filesystem mounts - free space (df -h) ######
Filesystem Size Used Avail Use% Mounted on
/dev/root 1.7G 1.3G 267M 83% /
devtmpfs 88M 0 88M 0% /dev
tmpfs 92M 0 92M 0% /dev/shm
tmpfs 92M 320K 92M 1% /run
tmpfs 92M 0 92M 0% /sys/fs/cgroup
tmpfs 92M 0 92M 0% /tmp
logs 5.0M 12K 5.0M 1% /var/log
Ramdisk 256M 0 256M 0% /run/shm
rune-logs 20M 12K 20M 1% /var/log/runeaudio
/dev/mmcblk0p1 90M 25M 65M 28% /boot
###### Loaded kernel modules ######
Module Size Used by
snd_soc_wm8804 7767 0
8192cu 540702 0
snd_soc_bcm2708_i2s 5657 0
regmap_mmio 2838 1 snd_soc_bcm2708_i2s
snd_soc_core 152794 2 snd_soc_wm8804,snd_soc_bcm2708_i2s
leds_gpio 2142 0
led_class 4162 1 leds_gpio
snd_compress 8219 1 snd_soc_core
snd_pcm_dmaengine 5533 1 snd_soc_core
regmap_spi 1941 2 snd_soc_wm8804,snd_soc_core
spi_bcm2708 4844 0
regmap_i2c 1685 2 snd_soc_wm8804,snd_soc_core
bcm2708_dmaengine 5224 0
i2c_bcm2708 4161 0
virt_dma 2309 1 bcm2708_dmaengine
snd_bcm2835 18168 0
snd_pcm 79264 3 snd_bcm2835,snd_soc_core,snd_pcm_dmaengine
snd_page_alloc 5192 1 snd_pcm
snd_timer 20362 1 snd_pcm
snd 60119 5 snd_bcm2835,snd_soc_core,snd_timer,snd_pcm,snd_compress
bcm2708_rng 1044 0
rng_core 4159 1 bcm2708_rng
nfs 205790 0
lockd 64174 1 nfs
sunrpc 237524 3 nfs,lockd
###### Network listening sockets (netstat -lnp) ######
Active Internet connections (only servers)
Proto Recv-Q Send-Q Local Address Foreign Address State PID/Program name
tcp 0 0 0.0.0.0:6600 0.0.0.0:* LISTEN 310/mpd
tcp 0 0 0.0.0.0:5002 0.0.0.0:* LISTEN 313/shairport
tcp 0 0 127.0.0.1:6379 0.0.0.0:* LISTEN 234/redis-server 12
tcp 0 0 0.0.0.0:111 0.0.0.0:* LISTEN 221/rpcbind
tcp 0 0 0.0.0.0:80 0.0.0.0:* LISTEN 239/nginx: master p
tcp 0 0 0.0.0.0:81 0.0.0.0:* LISTEN 239/nginx: master p
tcp 0 0 0.0.0.0:82 0.0.0.0:* LISTEN 239/nginx: master p
tcp 0 0 0.0.0.0:22 0.0.0.0:* LISTEN 216/sshd
tcp 0 0 0.0.0.0:49817 0.0.0.0:* LISTEN 247/rpc.statd
udp 0 0 0.0.0.0:817 0.0.0.0:* 221/rpcbind
udp 0 0 127.0.0.1:849 0.0.0.0:* 247/rpc.statd
udp 0 0 0.0.0.0:111 0.0.0.0:* 221/rpcbind
udp 0 0 0.0.0.0:137 0.0.0.0:* 292/nmbd
udp 0 0 0.0.0.0:138 0.0.0.0:* 292/nmbd
udp 0 0 0.0.0.0:56767 0.0.0.0:* 121/avahi-daemon: r
udp 0 0 0.0.0.0:5353 0.0.0.0:* 121/avahi-daemon: r
udp 0 0 0.0.0.0:58104 0.0.0.0:* 247/rpc.statd
Active UNIX domain sockets (only servers)
Proto RefCnt Flags Type State I-Node PID/Program name Path
unix 2 [ ACC ] STREAM LISTENING 5220 221/rpcbind /var/run/rpcbind.sock
unix 2 [ ACC ] STREAM LISTENING 6277 310/mpd /run/mpd.sock
unix 2 [ ACC ] STREAM LISTENING 3987 1/init /var/run/avahi-daemon/socket
unix 2 [ ACC ] STREAM LISTENING 2245 1/init /run/systemd/private
unix 2 [ ACC ] STREAM LISTENING 4046 1/init /run/dbus/system_bus_socket
unix 2 [ ACC ] SEQPACKET LISTENING 2258 1/init /run/udev/control
unix 2 [ ACC ] STREAM LISTENING 5598 227/php-fpm: master /var/run/php-display.sock
unix 2 [ ACC ] STREAM LISTENING 5601 227/php-fpm: master /var/run/php-db.sock
unix 2 [ ACC ] STREAM LISTENING 5604 227/php-fpm: master /var/run/php-command.sock
###### Network established sockets (netstat -np) ######
Active Internet connections (w/o servers)
Proto Recv-Q Send-Q Local Address Foreign Address State PID/Program name
tcp 0 0 127.0.0.1:58248 127.0.0.1:6379 TIME_WAIT -
tcp 0 0 127.0.0.1:6379 127.0.0.1:58270 ESTABLISHED 234/redis-server 12
tcp 0 0 127.0.0.1:58233 127.0.0.1:6379 TIME_WAIT -
tcp 0 0 127.0.0.1:58232 127.0.0.1:6379 TIME_WAIT -
tcp 0 0 127.0.0.1:80 127.0.0.1:43632 TIME_WAIT -
tcp 0 0 127.0.0.1:80 127.0.0.1:43624 TIME_WAIT -
tcp 0 0 127.0.0.1:6379 127.0.0.1:58269 ESTABLISHED 234/redis-server 12
tcp 0 0 127.0.0.1:58228 127.0.0.1:6379 TIME_WAIT -
tcp 0 0 127.0.0.1:80 127.0.0.1:43648 TIME_WAIT -
tcp 0 0 127.0.0.1:80 127.0.0.1:43521 TIME_WAIT -
tcp 0 0 127.0.0.1:6379 127.0.0.1:58125 ESTABLISHED 234/redis-server 12
tcp 0 0 127.0.0.1:58270 127.0.0.1:6379 ESTABLISHED 323/php
tcp 0 0 127.0.0.1:58269 127.0.0.1:6379 ESTABLISHED 337/php
tcp 0 0 127.0.0.1:80 127.0.0.1:43594 TIME_WAIT -
tcp 0 0 127.0.0.1:36622 127.0.0.1:6600 TIME_WAIT -
tcp 0 0 127.0.0.1:6379 127.0.0.1:58124 ESTABLISHED 234/redis-server 12
tcp 0 0 127.0.0.1:58124 127.0.0.1:6379 ESTABLISHED 220/php
tcp 0 0 127.0.0.1:58125 127.0.0.1:6379 ESTABLISHED 218/php
tcp 0 0 127.0.0.1:80 127.0.0.1:43512 TIME_WAIT -
Active UNIX domain sockets (w/o servers)
Proto RefCnt Flags Type State I-Node PID/Program name Path
unix 2 [ ] DGRAM 2243 1/init /run/systemd/notify
unix 2 [ ] DGRAM 2261 1/init /run/systemd/shutdownd
unix 3 [ ] STREAM CONNECTED 5596 227/php-fpm: master
unix 3 [ ] DGRAM 3248 88/systemd-udevd
unix 3 [ ] STREAM CONNECTED 6492 310/mpd /run/mpd.sock
unix 3 [ ] STREAM CONNECTED 4574 121/avahi-daemon: r /var/run/avahi-daemon/socket
unix 3 [ ] STREAM CONNECTED 4377 130/rpc.idmapd
unix 3 [ ] STREAM CONNECTED 6491 220/php
unix 3 [ ] STREAM CONNECTED 5529 239/nginx: master p
unix 3 [ ] STREAM CONNECTED 4354 121/avahi-daemon: r
unix 3 [ ] DGRAM 3247 88/systemd-udevd
unix 3 [ ] STREAM CONNECTED 4536 131/dbus-daemon /run/dbus/system_bus_socket
unix 3 [ ] STREAM CONNECTED 5528 239/nginx: master p
unix 3 [ ] STREAM CONNECTED 6202 131/dbus-daemon /run/dbus/system_bus_socket
unix 3 [ ] STREAM CONNECTED 6293 310/mpd
unix 3 [ ] STREAM CONNECTED 4469 1/init
unix 3 [ ] STREAM CONNECTED 5527 239/nginx: master p
unix 3 [ ] STREAM CONNECTED 4533 131/dbus-daemon
unix 3 [ ] STREAM CONNECTED 4312 128/avahi-daemon: c
unix 3 [ ] STREAM CONNECTED 5526 239/nginx: master p
unix 3 [ ] STREAM CONNECTED 4534 131/dbus-daemon
unix 3 [ ] STREAM CONNECTED 4535 131/dbus-daemon /run/dbus/system_bus_socket
unix 3 [ ] STREAM CONNECTED 4253 124/avahi-dnsconfd
unix 3 [ ] STREAM CONNECTED 6294 131/dbus-daemon /run/dbus/system_bus_socket
unix 3 [ ] STREAM CONNECTED 4311 121/avahi-daemon: r
unix 3 [ ] STREAM CONNECTED 6201 313/shairport
unix 3 [ ] STREAM CONNECTED 5597 227/php-fpm: master
unix 3 [ ] STREAM CONNECTED 4376 130/rpc.idmapd
###### Network interfaces (ip addr) ######
1: lo: mtu 65536 qdisc noqueue state UNKNOWN group default
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
inet 127.0.0.1/8 scope host lo
valid_lft forever preferred_lft forever
2: eth0: mtu 1500 qdisc pfifo_fast state DOWN group default qlen 1000
link/ether b8:27:eb:0a:e1:17 brd ff:ff:ff:ff:ff:ff
3: wlan0: mtu 1500 qdisc noop state DOWN group default qlen 1000
link/ether 80:1f:02:e6:7b:02 brd ff:ff:ff:ff:ff:ff
###### Network interfaces (ifconfig) ######
eth0: flags=4099 mtu 1500
ether b8:27:eb:0a:e1:17 txqueuelen 1000 (Ethernet)
RX packets 0 bytes 0 (0.0 B)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 0 bytes 0 (0.0 B)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
lo: flags=73 mtu 65536
inet 127.0.0.1 netmask 255.0.0.0
loop txqueuelen 0 (Local Loopback)
RX packets 2344 bytes 117158 (114.4 KiB)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 2344 bytes 117158 (114.4 KiB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
###### Network netctl profiles (netctl list) ######
wlan0
eth0
wlan0 netctl status
--------------------------------------------------------
● netctl@wlan0.service - Networking for netctl profile wlan0
Loaded: loaded (/usr/lib/systemd/system/netctl@.service; static)
Active: inactive (dead)
Docs: man:netctl.profile(5)
wlan0 netctl profile
--------------------------------------------------------
Description='wlan0 connection'
Interface=wlan0
ForceConnect=yes
SkipNoCarrier=yes
Connection=wireless
Security=wpa-config
WPAConfigFile='/etc/wpa_supplicant/wpa_supplicant.conf'
AutoWired=yes
IP=static
Address=('192.168.100.150/255.255.255.0')
Gateway='192.168.100.1'
DNS=('8.8.8.8' '8.8.4.4')
eth0 netctl status
--------------------------------------------------------
● netctl@eth0.service - eth0 dhcp connection
Loaded: loaded (/etc/systemd/system/netctl@eth0.service; enabled)
Active: failed (Result: exit-code) since Thu 1970-01-01 00:00:42 UTC; 20s ago
Docs: man:netctl.profile(5)
Process: 123 ExecStart=/usr/lib/network/network start %I (code=exited, status=1/FAILURE)
Main PID: 123 (code=exited, status=1/FAILURE)
eth0 netctl profile
--------------------------------------------------------
Description='eth0 dhcp connection'
Interface=eth0
Connection=ethernet
ForceConnect=yes
SkipNoCarrier=yes
IP=dhcp
###### Network wifi status (iwconfig) ######
lo no wireless extensions.
eth0 no wireless extensions.
wlan0 unassociated Nickname:""
Mode:Auto Frequency=2.412 GHz Access Point: Not-Associated
Sensitivity:0/0
Retry:off RTS thr:off Fragment thr:off
Encryption key:off
Power Management:off
Link Quality:0 Signal level:0 Noise level:0
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0
###### Kernel status (dmesg) ######
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Initializing cgroup subsys cpuacct
[ 0.000000] Linux version 3.12.19-2-ARCH (root@CS) (gcc version 4.8.2 20131219 (prerelease) (GCC) ) #1 PREEMPT Thu May 22 15:35:00 UTC 2014
[ 0.000000] CPU: ARMv6-compatible processor [410fb767] revision 7 (ARMv7), cr=00c5387d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT nonaliasing instruction cache
[ 0.000000] Machine: BCM2708
[ 0.000000] cma: CMA: reserved 8 MiB at 0b800000
[ 0.000000] Memory policy: ECC disabled, Data cache writeback
[ 0.000000] On node 0 totalpages: 49152
[ 0.000000] free_area_init_node: node 0, pgdat c064f190, node_mem_map c06e2000
[ 0.000000] Normal zone: 384 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 49152 pages, LIFO batch:15
[ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[ 0.000000] pcpu-alloc: [0] 0
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 48768
[ 0.000000] Kernel command line: dma.dmachans=0x7f35 bcm2708_fb.fbwidth=656 bcm2708_fb.fbheight=416 bcm2708.boardrev=0x3 bcm2708.serial=0xd70ae117 smsc95xx.macaddr=B8:27:EB:0A:E1:17 sdhci-bcm2708.emmc_clock_freq=250000000 vc_mem.mem_base=0xec00000 vc_mem.mem_size=0x10000000 ipv6.disable=1 selinux=0 plymouth.enable=0 smsc95xx.turbo_mode=N dwc_otg.lpm_enable=0 dwc_otg.fiq_split_enable=0 dwc_otg.fiq_fix_enable=0 console=tty1 root=/dev/mmcblk0p5 rootfstype=ext4 elevator=noop usbcore.old_scheme_first=1 coherent_pool=6M rootwait
[ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Memory: 179560K/196608K available (4392K kernel code, 282K rwdata, 1564K rodata, 201K init, 562K bss, 17048K reserved)
[ 0.000000] Virtual kernel memory layout:
vector : 0xffff0000 - 0xffff1000 ( 4 kB)
fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
vmalloc : 0xcc800000 - 0xff000000 ( 808 MB)
lowmem : 0xc0000000 - 0xcc000000 ( 192 MB)
modules : 0xbf000000 - 0xc0000000 ( 16 MB)
.text : 0xc0008000 - 0xc05d9550 (5958 kB)
.init : 0xc05da000 - 0xc060c504 ( 202 kB)
.data : 0xc060e000 - 0xc06548cc ( 283 kB)
.bss : 0xc06548cc - 0xc06e1250 ( 563 kB)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] NR_IRQS:394
[ 0.000000] sched_clock: 32 bits at 1000kHz, resolution 1000ns, wraps every 4294967ms
[ 0.000000] Switching to timer-based delay loop
[ 0.000000] Console: colour dummy device 80x30
[ 0.000000] console [tty1] enabled
[ 0.000618] Calibrating delay loop (skipped), value calculated using timer frequency.. 2.00 BogoMIPS (lpj=1000)
[ 0.000642] pid_max: default: 32768 minimum: 301
[ 0.000952] Mount-cache hash table entries: 512
[ 0.001867] Initializing cgroup subsys memory
[ 0.001954] Initializing cgroup subsys devices
[ 0.001973] Initializing cgroup subsys freezer
[ 0.001988] Initializing cgroup subsys blkio
[ 0.002000] Initializing cgroup subsys perf_event
[ 0.002204] CPU: Testing write buffer coherency: ok
[ 0.002653] Setting up static identity map for 0xc042dd80 - 0xc042ddb8
[ 0.004899] devtmpfs: initialized
[ 0.022896] VFP support v0.3: implementor 41 architecture 1 part 20 variant b rev 5
[ 0.025135] NET: Registered protocol family 16
[ 0.033977] DMA: preallocated 6144 KiB pool for atomic coherent allocations
[ 0.035394] bcm2708.uart_clock = 0
[ 0.037222] hw-breakpoint: found 6 breakpoint and 1 watchpoint registers.
[ 0.037242] hw-breakpoint: maximum watchpoint size is 4 bytes.
[ 0.037257] mailbox: Broadcom VideoCore Mailbox driver
[ 0.037339] bcm2708_vcio: mailbox at f200b880
[ 0.037446] bcm_power: Broadcom power driver
[ 0.037468] bcm_power_open() -> 0
[ 0.037481] bcm_power_request(0, 8)
[ 0.538198] bcm_mailbox_read -> 00000080, 0
[ 0.538218] bcm_power_request -> 0
[ 0.538502] Serial: AMBA PL011 UART driver
[ 0.538642] dev:f1: ttyAMA0 at MMIO 0x20201000 (irq = 83, base_baud = 0) is a PL011 rev3
[ 0.563617] bio: create slab at 0
[ 0.564901] SCSI subsystem initialized
[ 0.565308] usbcore: registered new interface driver usbfs
[ 0.565404] usbcore: registered new interface driver hub
[ 0.565685] usbcore: registered new device driver usb
[ 0.567984] Switched to clocksource stc
[ 0.586119] FS-Cache: Loaded
[ 0.586408] CacheFiles: Loaded
[ 0.599894] NET: Registered protocol family 2
[ 0.601142] TCP established hash table entries: 2048 (order: 2, 16384 bytes)
[ 0.601231] TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.601291] TCP: Hash tables configured (established 2048 bind 2048)
[ 0.601373] TCP: reno registered
[ 0.601397] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.601430] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.601882] NET: Registered protocol family 1
[ 0.603901] bcm2708_dma: DMA manager at f2007000
[ 0.604130] bcm2708_gpio: bcm2708_gpio_probe c061b800
[ 0.604611] vc-mem: phys_addr:0x00000000 mem_base=0x0ec00000 mem_size:0x10000000(256 MiB)
[ 0.777930] VFS: Disk quotas dquot_6.5.2
[ 0.778323] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 0.781940] aufs 3.12.x-20140512
[ 0.782053] msgmni has been set to 366
[ 0.785111] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
[ 0.785513] io scheduler noop registered (default)
[ 0.785538] io scheduler deadline registered
[ 0.785821] io scheduler cfq registered
[ 0.786951] BCM2708FB: allocated DMA memory 4be00000
[ 0.787083] BCM2708FB: allocated DMA channel 0 @ f2007000
[ 0.808506] Console: switching to colour frame buffer device 82x26
[ 0.811277] uart-pl011 dev:f1: no DMA platform data
[ 0.811910] vc-cma: Videocore CMA driver
[ 0.811931] vc-cma: vc_cma_base = 0x00000000
[ 0.811944] vc-cma: vc_cma_size = 0x00000000 (0 MiB)
[ 0.811955] vc-cma: vc_cma_initial = 0x00000000 (0 MiB)
[ 0.822284] brd: module loaded
[ 0.827907] loop: module loaded
[ 0.828290] vchiq: vchiq_init_state: slot_zero = 0xcb800000, is_master = 0
[ 0.829436] Loading iSCSI transport class v2.0-870.
[ 0.830727] usbcore: registered new interface driver ax88179_178a
[ 0.830862] usbcore: registered new interface driver smsc95xx
[ 0.831161] usbcore: registered new interface driver cdc_ncm
[ 0.831185] dwc_otg: version 3.00a 10-AUG-2012 (platform bus)
[ 1.031365] Core Release: 2.80a
[ 1.031399] Setting default values for core params
[ 1.031445] Finished setting default values for core params
[ 1.231510] Using Buffer DMA mode
[ 1.231535] Periodic Transfer Interrupt Enhancement - disabled
[ 1.231547] Multiprocessor Interrupt Enhancement - disabled
[ 1.231561] OTG VER PARAM: 0, OTG VER FLAG: 0
[ 1.231578] Dedicated Tx FIFOs mode
[ 1.232236] WARN::dwc_otg_hcd_init:1042: FIQ DMA bounce buffers: virt = 0xcbe14000 dma = 0x4be14000 len=9024
[ 1.232274] FIQ FSM acceleration enabled for :
Non-periodic Split Transactions
Periodic Split Transactions
High-Speed Isochronous Endpoints
[ 1.232303] dwc_otg: Microframe scheduler enabled
[ 1.232416] WARN::hcd_init:473: FIQ at 0xc032d988
[ 1.232438] WARN::hcd_init:474: FIQ ASM at 0xc032dc3c length 36
[ 1.232469] WARN::hcd_init:500: MPHI regs_base at 0xcc806000
[ 1.232500] dwc_otg bcm2708_usb: DWC OTG Controller
[ 1.232584] dwc_otg bcm2708_usb: new USB bus registered, assigned bus number 1
[ 1.232648] dwc_otg bcm2708_usb: irq 32, io mem 0x00000000
[ 1.232688] Init: Port Power? op_state=1
[ 1.232699] Init: Power Port (0)
[ 1.233113] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 1.233141] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.233159] usb usb1: Product: DWC OTG Controller
[ 1.233175] usb usb1: Manufacturer: Linux 3.12.19-2-ARCH dwc_otg_hcd
[ 1.233191] usb usb1: SerialNumber: bcm2708_usb
[ 1.233936] hub 1-0:1.0: USB hub found
[ 1.234097] hub 1-0:1.0: 1 port detected
[ 1.234603] dwc_otg: FIQ enabled
[ 1.234623] dwc_otg: NAK holdoff enabled
[ 1.234634] dwc_otg: FIQ split-transaction FSM enabled
[ 1.234656] Module dwc_common_port init
[ 1.235233] usbcore: registered new interface driver usb-storage
[ 1.235566] mousedev: PS/2 mouse device common for all mice
[ 1.236581] device-mapper: uevent: version 1.0.3
[ 1.237224] device-mapper: ioctl: 4.26.0-ioctl (2013-08-15) initialised: dm-devel@redhat.com
[ 1.237891] device-mapper: multipath: version 1.6.0 loaded
[ 1.237918] device-mapper: multipath round-robin: version 1.0.0 loaded
[ 1.237932] device-mapper: multipath queue-length: version 0.1.0 loaded
[ 1.237945] device-mapper: multipath service-time: version 0.2.0 loaded
[ 1.238126] sdhci: Secure Digital Host Controller Interface driver
[ 1.238143] sdhci: Copyright(c) Pierre Ossman
[ 1.238232] sdhci: Enable low-latency mode
[ 1.268044] mmc0: SDHCI controller on BCM2708_Arasan [platform] using platform's DMA
[ 1.268291] mmc0: BCM2708 SDHC host at 0x20300000 DMA 2 IRQ 77
[ 1.268392] sdhci-pltfm: SDHCI platform and OF driver helper
[ 1.268555] hidraw: raw HID events driver (C) Jiri Kosina
[ 1.269077] usbcore: registered new interface driver usbhid
[ 1.269098] usbhid: USB HID core driver
[ 1.269884] zram: Created 1 device(s) ...
[ 1.270504] TCP: cubic registered
[ 1.270531] Initializing XFRM netlink socket
[ 1.270574] NET: Registered protocol family 17
[ 1.270687] Key type dns_resolver registered
[ 1.277796] registered taskstats version 1
[ 1.279142] Waiting for root device /dev/mmcblk0p5...
[ 1.326281] mmc0: new high speed SDHC card at address 0007
[ 1.326930] mmcblk0: mmc0:0007 SD08G 7.42 GiB
[ 1.330337] mmcblk0: p1 p2 < p5 > p3
[ 1.434266] Indeed it is in host mode hprt0 = 00021501
[ 1.608111] usb 1-1: new high-speed USB device number 2 using dwc_otg
[ 1.619510] usb 1-1: New USB device found, idVendor=0424, idProduct=9512
[ 1.619540] usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[ 1.620360] hub 1-1:1.0: USB hub found
[ 1.620526] hub 1-1:1.0: 3 ports detected
[ 1.894210] usb 1-1.1: new high-speed USB device number 3 using dwc_otg
[ 1.905526] usb 1-1.1: New USB device found, idVendor=0424, idProduct=ec00
[ 1.905555] usb 1-1.1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[ 1.908529] smsc95xx v1.0.4
[ 1.953820] smsc95xx 1-1.1:1.0 eth0: register 'smsc95xx' at usb-bcm2708_usb-1.1, smsc95xx USB 2.0 Ethernet, b8:27:eb:0a:e1:17
[ 2.027166] usb 1-1.3: new high-speed USB device number 4 using dwc_otg
[ 2.040045] usb 1-1.3: New USB device found, idVendor=05e3, idProduct=0606
[ 2.040078] usb 1-1.3: New USB device strings: Mfr=0, Product=1, SerialNumber=0
[ 2.040096] usb 1-1.3: Product: USB2.0 Hub
[ 2.041110] hub 1-1.3:1.0: USB hub found
[ 2.041495] hub 1-1.3:1.0: 4 ports detected
[ 2.308339] usb 1-1.3.1: new high-speed USB device number 5 using dwc_otg
[ 2.321759] usb 1-1.3.1: New USB device found, idVendor=0aec, idProduct=3260
[ 2.321793] usb 1-1.3.1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 2.321810] usb 1-1.3.1: Product: USB Storage Device
[ 2.321827] usb 1-1.3.1: Manufacturer: Generic
[ 2.321843] usb 1-1.3.1: SerialNumber: 0AEC326000001A000
[ 2.322841] usb-storage 1-1.3.1:1.0: USB Mass Storage device detected
[ 2.326641] scsi0 : usb-storage 1-1.3.1:1.0
[ 2.401366] usb 1-1.3.2: new high-speed USB device number 6 using dwc_otg
[ 2.412972] usb 1-1.3.2: New USB device found, idVendor=0781, idProduct=556b
[ 2.413058] usb 1-1.3.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 2.413080] usb 1-1.3.2: Product: Cruzer Edge
[ 2.413097] usb 1-1.3.2: Manufacturer: SanDisk
[ 2.413117] usb 1-1.3.2: SerialNumber: 20060164501B079361C6
[ 2.414132] usb-storage 1-1.3.2:1.0: USB Mass Storage device detected
[ 2.415904] scsi1 : usb-storage 1-1.3.2:1.0
[ 2.490370] usb 1-1.3.4: new high-speed USB device number 7 using dwc_otg
[ 2.503099] usb 1-1.3.4: New USB device found, idVendor=7392, idProduct=7811
[ 2.503134] usb 1-1.3.4: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 2.503151] usb 1-1.3.4: Product: 802.
[ 2.503167] usb 1-1.3.4: Manufacturer: Realtek
[ 2.503183] usb 1-1.3.4: SerialNumber: 00e04c000001
[ 2.825401] EXT4-fs (mmcblk0p5): recovery complete
[ 2.828203] EXT4-fs (mmcblk0p5): mounted filesystem with ordered data mode. Opts: (null)
[ 2.828302] VFS: Mounted root (ext4 filesystem) on device 179:5.
[ 2.837778] devtmpfs: mounted
[ 2.838536] Freeing unused kernel memory: 200K (c05da000 - c060c000)
[ 3.330471] scsi 0:0:0:0: Direct-Access Generic USB Storage-CFC I19A PQ: 0 ANSI: 0 CCS
[ 3.334232] sd 0:0:0:0: [sda] Attached SCSI removable disk
[ 3.335120] scsi 0:0:0:1: Direct-Access Generic USB Storage-SDC I19A PQ: 0 ANSI: 0 CCS
[ 3.338813] sd 0:0:0:1: [sdb] Attached SCSI removable disk
[ 3.339622] scsi 0:0:0:2: Direct-Access Generic USB Storage-SMC I19A PQ: 0 ANSI: 0 CCS
[ 3.344351] sd 0:0:0:2: [sdc] Attached SCSI removable disk
[ 3.345522] scsi 0:0:0:3: Direct-Access Generic USB Storage-MSC I19A PQ: 0 ANSI: 0 CCS
[ 3.348726] sd 0:0:0:3: [sdd] Attached SCSI removable disk
[ 3.418653] scsi 1:0:0:0: Direct-Access SanDisk Cruzer Edge 2.01 PQ: 0 ANSI: 6
[ 3.421253] sd 1:0:0:0: [sde] 31266816 512-byte logical blocks: (16.0 GB/14.9 GiB)
[ 3.422739] sd 1:0:0:0: [sde] Write Protect is off
[ 3.422778] sd 1:0:0:0: [sde] Mode Sense: 43 00 00 00
[ 3.423481] sd 1:0:0:0: [sde] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 3.432678] sde: sde1
[ 3.436834] sd 1:0:0:0: [sde] Attached SCSI disk
[ 4.162297] RPC: Registered named UNIX socket transport module.
[ 4.162305] RPC: Registered udp transport module.
[ 4.162309] RPC: Registered tcp transport module.
[ 4.162313] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 4.401794] FS-Cache: Netfs 'nfs' registered for caching
[ 4.409444] systemd-modules-load[65]: Inserted module 'nfs'
[ 5.711201] EXT4-fs (mmcblk0p5): Mount option "nouser_xattr" will be removed by 3.5
Contact linux-ext4@vger.kernel.org if you think we should keep it.
[ 5.711275] EXT4-fs (mmcblk0p5): re-mounted. Opts: nouser_xattr,errors=remount-ro
[ 5.743308] bcm2708_rng_init=cc80a000
[ 5.743751] systemd-modules-load[65]: Inserted module 'bcm2708_rng'
[ 5.926817] systemd-modules-load[65]: Inserted module 'snd_bcm2835'
[ 6.079435] systemd-udevd[88]: starting version 212
[ 6.883138] bcm2708_i2c_init_pinmode(0,0)
[ 6.883170] bcm2708_i2c_init_pinmode(0,1)
[ 6.883457] bcm2708_i2c bcm2708_i2c.0: BSC0 Controller at 0x20205000 (irq 79) (baudrate 100k)
[ 6.886173] bcm2708_i2c_init_pinmode(1,2)
[ 6.886203] bcm2708_i2c_init_pinmode(1,3)
[ 6.886681] bcm2708_i2c bcm2708_i2c.1: BSC1 Controller at 0x20804000 (irq 79) (baudrate 100k)
[ 6.905200] bcm2708_spi bcm2708_spi.0: master is unqueued, this is deprecated
[ 6.908273] bcm2708_spi bcm2708_spi.0: SPI Controller at 0x20204000 (irq 80)
[ 7.267557] bcm2708-i2s bcm2708-i2s.0: Failed to create debugfs directory
[ 7.685689] FAT-fs (mmcblk0p1): Volume was not properly unmounted. Some data may be corrupt. Please run fsck.
[ 9.181397] smsc95xx 1-1.1:1.0 eth0: hardware isn't capable of remote wakeup
[ 11.343255] usbcore: registered new interface driver rtl8192cu
[ 42.415248] smsc95xx 1-1.1:1.0 eth0: hardware isn't capable of remote wakeup
[ 43.449155] smsc95xx 1-1.1:1.0 eth0: hardware isn't capable of remote wakeup
[ 57.576810] FAT-fs (sde1): utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!
[ 61.914238] cfg80211: Calling CRDA to update world regulatory domain
###### PHP backend ######
php version: 5.5.12
debug level: 0
Debug data collected in 10.332 seconds.
(My system-time looks pretty wierd, huh?)
Maybe you can get something out of it.
Update 4:
AirPlay works great. I wasn't able to use this feature in 0.2-beta (And Yes, it was enabled
), but it clealy works without any issues now
Update 5:
Then i have AirPlay playback, there's no info about it in theUI - but it's fine for me. It just showing the last played song from MPD. It also looks like it's hard for Chrome to get updates from the UI. Now the wheel keeps spinning again. I was able to access it again with Ctrl + Shift + R, and opening the UI in a new tab after that.
... and the last question for today:
Is there a action for the task/settings icon? (#id:db-homeSetup).