I just installed Rune V0.5 20180903 on a RPi 3B+ rev1.3 with a HIFIberry Digi+ Pro daughter board. I got Runo to work (its awesome) and Connected to Spotify but it only plays in analog. For some strange reason i can't get my S/PDIF DAC to play anything.
My DAC is good and plays with my cd transport. The i2s Kernal is the HiFiBerry Digi Pro and the output is HiFiBerry Digi (i2s), What am i missing?
Thanks for any help.
Kevin
Here's the full debug data https://pastebin.com/zSba1iGf
## RuneAudio HDMI & 3,5mm jack
dtparam=audio=off
## RuneAudio I2S-Settings
dtoverlay=hifiberry-digi-pro
# Uncomment to enable the lirc-rpi module
# Params: gpio_out_pin GPIO pin for output (default "17")
# gpio_in_pin GPIO pin for input (default "18")
# gpio_in_pull Pull up/down/off on the input pin
# (default "down")
# sense Override the IR receive auto-detection logic:
# (default "-1")
# softcarrier Turn the software carrier "on" or "off"
# (default "on")
# (default "off")
# LCD settings
# 180 degrees
# Normal
lcd_rotate=0
disable_splash=0 # set to 1 to disable boot splash
# Uncomment if you get no picture on HDMI for a default "safe" mode
# Uncomment this if your display has a black border of unused pixels visible
# and your display can output without overscan
# Uncomment the following to adjust overscan. Use positive numbers if console
# goes off screen, and negative if there is too much border
# Uncomment to force a console size. By default it will be display's size minus
# overscan.
# Uncomment if hdmi display is not detected and composite is being output
# Uncomment to force a specific HDMI mode (this will force VGA)
# Uncomment to force a HDMI mode rather than DVI. This can make audio work in
# DMT (computer monitor) modes
# Uncomment to set monitor mode to DMT
# Uncomment to increase signal to HDMI, if you have interference, blanking, or
# no display
# setting the max usb current to 1200mA
max_usb_current=1
# memory options
gpu_mem=16
## Some overclocking settings, govenor is set to ondemand as standard
## The values below are valid for the B+ and Zero models
## Overclocking should not be needed for the 2B, 3B and 3B+ models
## See your documentation for A and B models
## None
## Modest
## Medium - fast enough for normal (MPD) use, airplay may need more capacity
## High
## Turbo
## General CPU settings
force_turbo=1
# Lowering max CPU temperature from 85 (standard) to 70 or 75 degrees gives some protection when (force) turbo is set
# If the max temp is reached the cpu will autmatically be throttled back
# Boot delay sometimes needs to be set to higher values when overclocking is enabled
# Default boot delay is 1 second, 3B+ needs a delay of 2
boot_delay=2
initramfs initramfs-linux.img followkernel
##################################################
###### System load statistics (procinfo -H) ######
Memory: Total Used Free Buffers
RAM: 973.57MiB 276.75MiB 696.82MiB 29.54MiB
Swap: 0.00B 0.00B 0.00B
Bootup: Sat Mar 9 16:00:42 2019 Load average: 0.25 0.17 0.11 1/144 3880
user : 00:02:46.15 2.6% page in : 158085
nice : 00:00:09.27 0.1% page out: 20320
system: 00:00:31.39 0.5% page act: 20631
IOwait: 00:00:33.06 0.5% page dea: 0
hw irq: 00:00:00.00 0.0% page flt: 1494612
sw irq: 00:00:01.60 0.0% swap in : 0
idle : 01:44:15.48 96.3% swap out: 0
uptime: 00:27:11.03 context : 1040266
irq 16: 0 irq 55: 0
irq 17: 192344 irq 56: 0
irq 21: 0 irq 59: 0
irq 23: 815 irq 62: 3395022
irq 24: 2 irq 83: 18
irq 46: 0 irq 86: 938
irq 48: 0 irq 87: 157
irq 50: 0 irq 92: 224733
irq 51: 174 irq 169: 0 17 Edge usb-001:0
irq 54: 5007
mmcblk0 4143r 8 mmcblk0p2 3987r
mmcblk0p1 114r sda 285r 0w
eth0 TX 0.00B RX 0.00B wlan0 TX 474.70KiB RX 362.46KiB
lo TX 828.11KiB RX 828.11KiB
###### Active processes (pstree) ######
systemd-+-avahi-daemon---avahi-daemon
|-chronyd
|-crond
|-dbus-daemon
|-devmon---udevil
|-dhcpcd
|-haveged
|-hciattach
|-ifplugd
|-mpd---4*[{mpd}]
|-nginx---nginx
|-nmbd
|-php-fpm---3*[php-fpm]
|-python
|-redis-server---3*[{redis-server}]
|-rune_PL_wrk
|-rune_SY_wrk---sh---debug_collector---sh---pstree
|-sh---sleep
|-smbd-+-cleanupd
| `-smbd-notifyd
|-sshd
|-systemd-journal
|-systemd-resolve
|-systemd-udevd
|-winbindd---3*[winbindd]
|-wpa_actiond
`-wpa_supplicant
###### Audio backend ######
Advanced Linux Sound Architecture Driver Version k4.14.34-1-ARCH.
Card list: (/proc/asound/cards)
--------------------------------------------------
0 [sndrpihifiberry]: HifiberryDigi - snd_rpi_hifiberry_digi
snd_rpi_hifiberry_digi
PLAYBACK devices: (aplay -l)
--------------------------------------------------
**** List of PLAYBACK Hardware Devices ****
card 0: sndrpihifiberry [snd_rpi_hifiberry_digi], device 0: HiFiBerry Digi+ Pro HiFi wm8804-spdif-0 []
Subdevices: 1/1
Subdevice #0: subdevice #0
PCM devices: (aplay -L)
--------------------------------------------------
null
Discard all samples (playback) or generate zero samples (capture)
pulse
PulseAudio Sound Server
default:CARD=sndrpihifiberry
snd_rpi_hifiberry_digi,
Default Audio Device
sysdefault:CARD=sndrpihifiberry
snd_rpi_hifiberry_digi,
Default Audio Device
Simple mixer controls: (amixer scontrols)
--------------------------------------------------
card 0:
Simple mixer control 'Tx Source',0
Mixer controls: (amixer controls)
--------------------------------------------------
card 0:
numid=1,iface=MIXER,name='Tx Source'
MPD audio outputs status: (mpc outputs)
--------------------------------------------------
Output 1 (snd_rpi_hifiberry_digi) is enabled