RuneAudio 0.5-beta for most Raspberry Pi models

[bondoz]

Noob here my first RPi box, please have pity on me. I read and searched all day for a solution so before my wife divorces me...

I just installed Rune V0.5 20180903 on a RPi 3B+ rev1.3 with a HIFIberry Digi+ Pro daughter board. I got Runo to work (its awesome) and Connected to Spotify but it only plays in analog. For some strange reason i can't get my S/PDIF DAC to play anything.

My DAC is good and plays with my cd transport. The i2s Kernal is the HiFiBerry Digi Pro and the output is HiFiBerry Digi (i2s), What am i missing?

Thanks for any help.
Kevin

Here's the full debug data https://pastebin.com/zSba1iGf

## RuneAudio HDMI & 3,5mm jack
dtparam=audio=off
## RuneAudio I2S-Settings
dtoverlay=hifiberry-digi-pro
# Uncomment to enable the lirc-rpi module
# Params: gpio_out_pin GPIO pin for output (default "17")
# gpio_in_pin GPIO pin for input (default "18")
# gpio_in_pull Pull up/down/off on the input pin
# (default "down")
# sense Override the IR receive auto-detection logic:
# (default "-1")
# softcarrier Turn the software carrier "on" or "off"
# (default "on")
# (default "off")
# LCD settings
# 180 degrees
# Normal
lcd_rotate=0
disable_splash=0 # set to 1 to disable boot splash
# Uncomment if you get no picture on HDMI for a default "safe" mode
# Uncomment this if your display has a black border of unused pixels visible
# and your display can output without overscan
# Uncomment the following to adjust overscan. Use positive numbers if console
# goes off screen, and negative if there is too much border
# Uncomment to force a console size. By default it will be display's size minus
# overscan.
# Uncomment if hdmi display is not detected and composite is being output
# Uncomment to force a specific HDMI mode (this will force VGA)
# Uncomment to force a HDMI mode rather than DVI. This can make audio work in
# DMT (computer monitor) modes
# Uncomment to set monitor mode to DMT
# Uncomment to increase signal to HDMI, if you have interference, blanking, or
# no display
# setting the max usb current to 1200mA
max_usb_current=1
# memory options
gpu_mem=16
## Some overclocking settings, govenor is set to ondemand as standard
## The values below are valid for the B+ and Zero models
## Overclocking should not be needed for the 2B, 3B and 3B+ models
## See your documentation for A and B models
## None
## Modest
## Medium - fast enough for normal (MPD) use, airplay may need more capacity
## High
## Turbo
## General CPU settings
force_turbo=1
# Lowering max CPU temperature from 85 (standard) to 70 or 75 degrees gives some protection when (force) turbo is set
# If the max temp is reached the cpu will autmatically be throttled back
# Boot delay sometimes needs to be set to higher values when overclocking is enabled
# Default boot delay is 1 second, 3B+ needs a delay of 2
boot_delay=2
initramfs initramfs-linux.img followkernel


##################################################


###### System load statistics (procinfo -H) ######
Memory: Total Used Free Buffers
RAM: 973.57MiB 276.75MiB 696.82MiB 29.54MiB
Swap: 0.00B 0.00B 0.00B

Bootup: Sat Mar 9 16:00:42 2019 Load average: 0.25 0.17 0.11 1/144 3880

user : 00:02:46.15 2.6% page in : 158085
nice : 00:00:09.27 0.1% page out: 20320
system: 00:00:31.39 0.5% page act: 20631
IOwait: 00:00:33.06 0.5% page dea: 0
hw irq: 00:00:00.00 0.0% page flt: 1494612
sw irq: 00:00:01.60 0.0% swap in : 0
idle : 01:44:15.48 96.3% swap out: 0
uptime: 00:27:11.03 context : 1040266

irq 16: 0 irq 55: 0
irq 17: 192344 irq 56: 0
irq 21: 0 irq 59: 0
irq 23: 815 irq 62: 3395022
irq 24: 2 irq 83: 18
irq 46: 0 irq 86: 938
irq 48: 0 irq 87: 157
irq 50: 0 irq 92: 224733
irq 51: 174 irq 169: 0 17 Edge usb-001:0
irq 54: 5007

mmcblk0 4143r 8 mmcblk0p2 3987r
mmcblk0p1 114r sda 285r 0w

eth0 TX 0.00B RX 0.00B wlan0 TX 474.70KiB RX 362.46KiB
lo TX 828.11KiB RX 828.11KiB


###### Active processes (pstree) ######
systemd-+-avahi-daemon---avahi-daemon
|-chronyd
|-crond
|-dbus-daemon
|-devmon---udevil
|-dhcpcd
|-haveged
|-hciattach
|-ifplugd
|-mpd---4*[{mpd}]
|-nginx---nginx
|-nmbd
|-php-fpm---3*[php-fpm]
|-python
|-redis-server---3*[{redis-server}]
|-rune_PL_wrk
|-rune_SY_wrk---sh---debug_collector---sh---pstree
|-sh---sleep
|-smbd-+-cleanupd
| `-smbd-notifyd
|-sshd
|-systemd-journal
|-systemd-resolve
|-systemd-udevd
|-winbindd---3*[winbindd]
|-wpa_actiond
`-wpa_supplicant


###### Audio backend ######
Advanced Linux Sound Architecture Driver Version k4.14.34-1-ARCH.

Card list: (/proc/asound/cards)
--------------------------------------------------
0 [sndrpihifiberry]: HifiberryDigi - snd_rpi_hifiberry_digi
snd_rpi_hifiberry_digi


PLAYBACK devices: (aplay -l)
--------------------------------------------------
**** List of PLAYBACK Hardware Devices ****
card 0: sndrpihifiberry [snd_rpi_hifiberry_digi], device 0: HiFiBerry Digi+ Pro HiFi wm8804-spdif-0 []
Subdevices: 1/1
Subdevice #0: subdevice #0


PCM devices: (aplay -L)
--------------------------------------------------
null
Discard all samples (playback) or generate zero samples (capture)
pulse
PulseAudio Sound Server
default:CARD=sndrpihifiberry
snd_rpi_hifiberry_digi,
Default Audio Device
sysdefault:CARD=sndrpihifiberry
snd_rpi_hifiberry_digi,
Default Audio Device


Simple mixer controls: (amixer scontrols)
--------------------------------------------------
card 0:
Simple mixer control 'Tx Source',0


Mixer controls: (amixer controls)
--------------------------------------------------
card 0:
numid=1,iface=MIXER,name='Tx Source'


MPD audio outputs status: (mpc outputs)
--------------------------------------------------
Output 1 (snd_rpi_hifiberry_digi) is enabled

[janui]

Hi bondoz,

I just installed Rune V0.5 20180903 on a RPi 3B+ rev1.3 with a HIFIberry Digi+ Pro daughter board. I got Runo to work (its awesome) and Connected to Spotify but it only plays in analog. For some strange reason i can't get my S/PDIF DAC to play anything.

The Spotify support in RuneAudio stopped working some time ago. In the UI you can see this:

Due to the Spotify upgrade of May 2018 the Spotify client no longer works

For more information you can look here: post25345.html?hilit=spotify%20janui#p25345
janui

[bondoz]

Hi Janui,,,Thank you for the response.

Sorry my post was unclear.
"Spotify Connect" is not the issue - that works along with playing from the network share and usb BUT only in analog.

The issue is that when i play any music thru the HIFIBerry digi i don't get a Digital output. My DAC fails to see/process a signal. I selected all the correct options in the software. I think there's something wrong in my config but can't seem to find it.

Ty
Kevin


UPDATE: I wiped it and started over. It works like its supposed too now.

I also found this error but couldn't seem to resolve it -

Mar 09 16:01:31 runeaudio sh[470]: alsaaudio.ALSAAudioError: Unable to find mixer control TX,0 [default]
Mar 09 16:01:36 runeaudio systemd[1]: Reloading.
Mar 09 16:01:37 runeaudio systemd[1]: Starting Music Player Daemon...

Should've been
Mar 09 16:01:31 runeaudio sh[470]: alsaaudio.ALSAAudioError: Unable to find mixer control "TX Source",0 [default]

[janui]

Hi bondoz,
Good that eveything is working. I am very interested in the error message:

...I also found this error but couldn't seem to resolve it -
Mar 09 16:01:31 runeaudio sh[470]: alsaaudio.ALSAAudioError: Unable to find mixer control TX,0 [default]
Mar 09 16:01:36 runeaudio systemd[1]: Reloading.
Mar 09 16:01:37 runeaudio systemd[1]: Starting Music Player Daemon...
Should've been:
Mar 09 16:01:31 runeaudio sh[470]: alsaaudio.ALSAAudioError: Unable to find mixer control "TX Source",0 [default]...

If it is still appearing, could you post the ouput of these commands:

Code: Select all

dmesg | grep -i -E 'alsa|mpd' | grep -v audit
journalctl | grep -i -E 'alsa|mpd' | grep -v audit

Thanks in advance,
janui

[nic]

devmode.jpg (79.59 KiB) Viewed 1927 times

A while ago , I did a gitpull , rebooted and everything was fine . Today I found that devmode seems to be kaput . I get Guru Meditation #0000022.65045032 errot . Any ideas what is going on ? Everything works fine apart from devmode

[R101]

Hi R101,

Rune v0.4b has been able to play the BBC m3u8 feeds since the MPD upgrade addon became available. Rune v0.5 does not play them, so this does appear to be a regression.

Thanks for the clarification. Can you tell me which version of MPD you are using on v04b.
janui

Hi janui,

Due to the fact that Rune was throwing up various problems, I reinstalled 0.4b from scratch. The MPD update addon installed v0.21.5, which works OK, so there does not appear to be a problem with the new MPD version.

[konki]

Hi, I just installed the 0.5beta version. Version 0.3beta have worked since 2015 on a pi2 until a bug prevents updating the musical index. I added the addon RuneUI enhancement to version 0.5. Everything is working except the RuneUI interface on android and ios.
I have this error messages:

Code: Select all

Warning: Invalid argument supplied for foreach() in /srv/http/app/templates/enhancebody.php on line 78
Warning: scandir(/srv/http/assets/img/coverarts): failed to open dir: No such file or directory in /srv/http/app/templates/enhancebody.php on line 105
Warning: scandir(): (errno 13): Permission denied in /srv/http/app/templates/enhancebody.php on line 105
Warning: array_slice() expects parameter 1 to be array, boolean given in /srv/http/app/templates/enhancebody.php on line 105

does anyone have a solution?
Thanks
konki

[janui]

Hi konki,

...I have this error messages:...

I don't quite understand what is going on here, the file /srv/http/app/templates/enhancebody.php and directory /srv/http/assets/img/coverarts are not part of the standard distribution. It looks like you have installed something extra, maybe Rern's addons. If so, I suggest you post any questions about this in the thread concerning the extra installed components.
janui

[janui]

Hi R101,

...The MPD update addon installed v0.21.5, which works OK...

Thanks for the confirmation.
janui

[janui]

Hi nic,

...Today I found that devmode seems to be kaput...

I am not sure that this will fix it, but I would try a manual git pull via SSH. These are the commands which I normally use:

Code: Select all

cd /srv/http/
git config --global core.editor "nano"
git config user.email "any@body.com"
git config user.name "anybody"
git stash
git add .
git pull --no-edit
cd /home
chown -R http.http /srv/http/
find /srv/http/ -type f -exec chmod 644 {} \;
find /srv/http/ -type d -exec chmod 755 {} \;
find /etc -name *.conf -exec chmod 644 {} \;
find /usr/lib/systemd/system -name *.service -exec chmod 644 {} \;
chmod 644 /etc/nginx/html/50x.html
chmod 777 /run
chmod 755 /srv/http/command/*
chmod 755 /srv/http/db/redis_datastore_setup
chmod 755 /srv/http/db/redis_acards_details
chmod 755 /etc/X11/xinit/start_chromium.sh
chown mpd.audio /mnt/MPD/*
chown mpd.audio /mnt/MPD/USB/*
chmod 777 /mnt/MPD/USB
chmod 777 /mnt/MPD/USB/*
chown -R mpd.audio /var/lib/mpd
/srv/http/command/rune_shutdown
reboot

Any errors are normally OK, except the git pull.
If you still have problems you can reinstall 0.5b via SSH. All your settings should be retained. Use these commands:

Code: Select all

cd /var/www
/srv/http/command/rune_shutdown
git config user.email "any@body.com"
git config user.name "anybody"
git config --global core.editor "nano"
umount http-tmp
rm -rf /var/www/{*,.*}
git clone -b 0.5b https://github.com/gearhead/RuneUI.git/ /var/www
find /srv/http/ -type f -exec chmod 644 {} \;
find /srv/http/ -type d -exec chmod 755 {} \;
find /etc -name *.conf -exec chmod 644 {} \;
find /usr/lib/systemd/system -name *.service -exec chmod 644 {} \;
chmod 644 /etc/nginx/html/50x.html
chmod 777 /run
chmod 755 /srv/http/command/*
chmod 755 /srv/http/db/redis_datastore_setup
chmod 755 /srv/http/db/redis_acards_details
chmod 755 /etc/X11/xinit/start_chromium.sh
chown mpd.audio /mnt/MPD/*
chown mpd.audio /mnt/MPD/USB/*
chmod 777 /mnt/MPD/USB
chmod 777 /mnt/MPD/USB/*
chown -R mpd.audio /var/lib/mpd
reboot

janui